Accessing Rootstown Campus Wireless Network

These are the instructions to access the Rootstown Campus Wireless network. Most devices except for Windows devices require special setup before you can connect. Please find the instructions for your device below. It is recommended to use the biomed network when you are at school because the guest wireless network may not work as well.

Windows

  1. Click the Wi-Fi icon on the taskbar, near the bottom right of the screen.

  2. Find the “biomed” SSID and click it and then click “Connect”.

    image3.png

  3. For Username and Password, type in your full school email address (Example: jdoe26@bmsastem.org) and type in the password for your school email account and click “sign in”.Note- You may need to enter the information more than once before it will take. Make sure that you are entering the correct email and password.

    image1.png

Mac

  1. In order to use the school network with a Mac, you must install a profile or else it will continue to loop and you will not be able to connect. The instructions may require administrative privileges you may want to install the profile at home to get help from a parent/guardian if your account does not have administrative privileges. Click Here to Download the Profile.
  2. Find the downloaded profile and open it.

  3. A dialog box will pop up that says “Are you sure you want to install “Bio-Med Rootstown Wi-Fi”. Click continue and click continue again if it asks you a second time.

    image13.png

  4. On the “Enterprise Network” screen, leave the username and password blank and click “install”

    image7.png

  5. Another dialog box will pop up asking for your Mac username credentials. Go ahead and enter your credentials and press “ok”. You may need administrative privileges in order to complete this step.

  6. After the profile is installed, click the Wi-Fi icon on the menu bar at the top and click the “biomed” SSID.

    image2.png

  7. For Username and Password, type in your full school email address (Example: jdoe26@bmsastem.org) and type in the password for your school email account and click “Join”.

    image4.png

Note- You may need to enter the information more than once before it will take. Make sure that you are entering the correct email and passwords.

Chromebook and Android Devices

  1. Go to the wireless network settings of the device where you can select the wireless network. There is usually a Wi-Fi icon to select to get to this.

  2. Select the “biomed” SSID. The “Join Wi-Fi network” dialog box will appear.

    image6.png

  3. Enter the information as follows:

    EAP Method: EAP-TTLSEAP

    Phase 2 authentication    : PAPServer

    CA Certificate: Do not check

    Identity:     your school email, including the domain name (example: jdoe26@bmsastem.org)

    Password:     Your school email account password

    Press "Connect" once this information is entered and you should be connected .Note- If you have signed into your school account on your Chromebook outside of school, the above settings (except for Identity and password) may already be configured. If this is the case, you will just need to enter your email and password). You may need to enter the information more than once before it will take. Make sure that you are entering the correct email and password.

    image10.png


iOS Devices (iPad/iPhone)

  1. In order to use the school network with an iOS device, you must install a profile or else you will not be able to connect. Download this profile onto your iPad

  2. Go to the Settings app. Near the top of the settings app, there should be an option that says “Profile Downloaded”. Tap to open.

    image9.png

  3. A dialog box pops up that has the words “Install” on the top right corner. Tap install. A warning may show up saying that the profile is not signed. Go ahead and tap “install again”. On the Install Profile box, click “Install” written in red.

    image11.png

    image8.png

  4. Two other dialog boxes will appear that say “Enter Username” and “Enter “Password”. Leave them both blank and press “Next” to both of them. You will get confirmation that the profile has been installed

    image14.png

    image16.png


  5. Go to the Wi-Fi settings in the settings app select the “biomed” SSID.

    image15.png

  6. For Username and Password, type in your full school email address (Example: jdoe26@bmsastem.org) and type in the password for your school email account and click “Join”.

    2jQs69GILE3fiCbLZZvfzTLmPYg8Zi3eJioprnlKfSdcWPKFwEfsTHzTpeUeqgQOYKI6zHyvNUYd7iPQutSn5yn8M4rSWTPBEbZ42zc-pkboQPwEzvfwFSlLO31-XsrNfly2_vrsfl60ls-hhEbf.png

Note: You may need to enter the information more than once before it will take. Make sure that you are entering the correct email and password.

Back to Home